Portfolio
Concrete floor with topping at a production and warehouse facility in Ramenskoye

CONCRETE FLOOR WITH TOPPING AT THE PRODUCTION AND WAREHOUSE FACILITY IN RAMENSKOYE

WE HAVE SAVED FOR THE CLIENT 579 900 ₽

20%Economy

FLOOR ENGINEERING CONSTRUCTION Concrete floor with topping at a production and warehouse facility in Ramenskoye

Moscow region, Ramenskoye, Safonovskoye highway, industrial zone

Characteristics and description
Company name REMZ POLYUS LLC
The purpose of the floor and the room itself Concrete floor with topping at a production and warehouse facility in Ramenskoye
Type of floor topping floors
Thickness of the concrete layer 18 cm
Room area 426 m²

Customer needs AND THE OPTIMAL ENGINEERING SOLUTION

factors taken into account when developing the floor design

WE HAVE SELECTED THE OPTIMAL ENGINEERING SOLUTION

At the time of contacting our company, the customer had not yet set up a base at the facility. Accordingly, in addition to the main work on the implementation of the industrial floor, it was necessary to perform a rather long preliminary stage.

The technical solution was prepared by the chief designer as follows: full–fledged preparation of a sandy base; installation of a concrete floor with an average thickness of 18 cm with a hardener and reinforcement with a double layer of reinforcement, as well as the installation of an external ramp.

Terms of work

Number of days for all work: 20

Requirements for the quality of work

Floors must comply with SNiP 2.03. 13-88

Appearance of floors

Must look presentable

Durability

Service life of floors without repair (years): 10

Total cost

Budget within the framework of: 2 899 500 ₽

Concrete floor with topping at a production and warehouse facility in Ramenskoye: The object before the start of work — The object before the start of work

Floor arrangement ACCORDING TO THE ENGINEERING SOLUTION FOR THE OBJECT: REMZ POLYUS LLC

how we implemented this floor design

FEATURES OF THE WORK

During the preparation of the foundation, we had to try hard, since the sand level had to be greatly raised. Large machinery was used – ice rinks, tractors.

At the time of work with the base, there was a gap of about half a meter between the walls of the building and the base. We covered this void with styrofoam insulation, and also foamed it to remove even small cracks.

Between the street ramp, which was arranged in front of the gate, and the room, we installed a non–removable formwork - a deformation seam. This is an expensive and labor-intensive solution, but at the same time effective and reliable.

OUR RESULTS

When handing over the object, the customer pointed out a couple of flaws – there was a gap near one of the walls, and in two places the coating remained slightly rough. Both points were settled at the sealing stage: the gap was sealed, and the irregularities were smoothed out. As a result, the customer was given a floor of proper quality for use.

Stages of implementation engineering design of the floor

engineering design of the floor

Tamping with a vibratory plate near the walls

Compaction of the base with a vibrating roller

The film has been laid; the insulating joint has been arranged

Concrete pump, topping and varnish in place

Compacting the concrete with a deep vibrator

A moisture-retaining impregnation has been applied

The result of floor engineeringDELIVERED ON TIME, STANDARD, TECHNOLOGICAL INDUSTRIAL FLOORS AT THE FACILITY REMZ POLYUS LLC

SEE THE RESULT OF OUR WORK

READ REVIEWS OUR SATISFIED CUSTOMERS

Reviews that we managed to collect between production cycles at our facilities

ReviewsABOUT THE PROFTEHPOL PROJECT

We are well aware that reviews of companies can be very different. Working in the construction market for more than 15 years, we have faced various situations.

We have both satisfied customers and those who are not. But, there is one important thing: we always bring the cycles of our provision to the end. If a client has problems, then we do not leave him with them, but settle them to a full and final conclusion.

Working with us, you can be sure that we will make you an industrial floor that is exactly right for the task for which you needed it.

Thanks to a good knowledge of the technology of industrial floors, we have gathered a lot of practical experience in using floor structures in various difficult places. We solve non-trivial problems and often, when we take an order, 3-4 companies have already tried to take it before us, but refused due to the complexity of the object.

Our clients Which we are proud of

for which we have made good floors